Description
The TEIN MONO RACING suspension package for Subaru BRZ / Toyota 86 / Scion FR-S applications detailed below is intended for frequent track use and deliberate chassis setup. Its spring, damper and mounting configuration should be selected as a complete application rather than by vehicle name alone.
Design and adjustment
MONO RACING uses a monotube layout and sport-focused damper settings. Its adjustment hardware provides a platform for tuning ride height and suspension response around the vehicle’s tires, alignment and intended circuit use.
Camber/caster-adjustable mounts and eccentric lower-bracket hardware depend on suspension design and application. Spring substitutions or custom valving require confirmation before ordering; they are not assumed to be included.
Product identification
| Item | Detail |
|---|---|
| Manufacturer part number | VSTD8-K1LS1 |
| Series | MONO RACING |
Application-specific specifications
| Application | Front spring rate | Rear spring rate | Front reference height change | Rear reference height change |
|---|---|---|---|---|
| Subaru BRZ 2013–2016 (ZCA), 2000 cc, RWD | 10 kgf/mm | 10 kgf/mm | -40 mm (-1.6 in) | -40 mm (-1.6 in) |
| Subaru BRZ 2017–2021 (ZCA), 2000 cc, RWD | 10 kgf/mm | 10 kgf/mm | -40 mm (-1.6 in) | -40 mm (-1.6 in) |
| Toyota 86 2017–2021 (ZNA), 2000 cc, RWD | 10 kgf/mm | 10 kgf/mm | -40 mm (-1.6 in) | -40 mm (-1.6 in) |
| Scion FR-S 2012–2016 (ZNA), 2DR/4CYL, 2000 cc, RWD | 10 kgf/mm | 10 kgf/mm | -40 mm (-1.6 in) | -40 mm (-1.6 in) |
Height figures are changes relative to the original suspension: negative values indicate lowering and positive values indicate a raised height. Inch figures are rounded conversions. Actual installed height depends on vehicle condition, equipment and setup.
| Application | Front upper mount | Rear upper mount |
|---|---|---|
| Subaru BRZ 2013–2016 (ZCA), 2000 cc, RWD | CAMBER CASTER ADJ | Pillow-ball mount |
| Subaru BRZ 2017–2021 (ZCA), 2000 cc, RWD | CAMBER CASTER ADJ | Pillow-ball mount |
| Toyota 86 2017–2021 (ZNA), 2000 cc, RWD | CAMBER CASTER ADJ | Pillow-ball mount |
| Scion FR-S 2012–2016 (ZNA), 2DR/4CYL, 2000 cc, RWD | CAMBER CASTER ADJ | Pillow-ball mount |
| Application | Recommended front height-change range | Recommended rear height-change range |
|---|---|---|
| Subaru BRZ 2013–2016 (ZCA), 2000 cc, RWD | -50 to -30 mm | -50 to -30 mm |
| Subaru BRZ 2017–2021 (ZCA), 2000 cc, RWD | -50 to -30 mm | -50 to -30 mm |
| Toyota 86 2017–2021 (ZNA), 2000 cc, RWD | -50 to -30 mm | -50 to -30 mm |
| Scion FR-S 2012–2016 (ZNA), 2DR/4CYL, 2000 cc, RWD | -50 to -30 mm | -50 to -30 mm |
Vehicle application
| Years / production dates | Make | Model | Chassis | Trim / restriction | Engine displacement | Drivetrain | Market |
|---|---|---|---|---|---|---|---|
| 2013–2016 | SUBARU | BRZ | ZCA | See installation notes | 2000 cc | RWD | USA |
| 2017–2021 | SUBARU | BRZ | ZCA | See installation notes | 2000 cc | RWD | USA |
| 2017–2021 | TOYOTA | 86 | ZNA | See installation notes | 2000 cc | RWD | USA |
| 2012–2016 | SCION | FR-S | ZNA | 2DR/4CYL | 2000 cc | RWD | USA |
Match the chassis, market and equipment above. Dates shown for non-US markets can be production dates rather than US model years; an open-ended application is not confirmation for a later redesigned chassis.
Included configuration
The application record identifies springs as included with this suspension kit. Upper-mount configuration is shown separately above; components marked as original are reused from the vehicle.
Installation and setup
Set the suspension within its application-specific recommended height range, check clearance through steering and suspension travel, and align the vehicle after fitting. Change damping settings progressively where adjustment is available; the firmest setting is not automatically the most suitable.
Application-specific installation notes
- Subaru BRZ 2013–2016 (ZCA): Rear: interior needs to be cut or removed, to avoid interference. Camber adjustment washers with different offsets are available (sold separately). From the positive angle set with the included washers, replace the washers with optional washers SPS12-R16100-25 to set the angle further positive, and with SPS12-R16100-05 to set to negative direction. From the negative angle set with the included washers, replace the washers with optional washers SPS12-R16100-05 to set the angle further negative, and with SPS12-R16100-25 to set to positive direction (both sold separately).
- Subaru BRZ 2017–2021 (ZCA): Rear: interior needs to be cut or removed, to avoid interference. Camber adjustment washers with different offsets are available (sold separately). From the positive angle set with the included washers, replace the washers with optional washers SPS12-R16100-25 to set the angle further positive, and with SPS12-R16100-05 to set to negative direction. From the negative angle set with the included washers, replace the washers with optional washers SPS12-R16100-05 to set the angle further negative, and with SPS12-R16100-25 to set to positive direction (both sold separately).
- Toyota 86 2017–2021 (ZNA): Rear: interior needs to be cut or removed, to avoid interference. Camber adjustment washers with different offsets are available (sold separately). From the positive angle set with the included washers, replace the washers with optional washers SPS12-R16100-25 to set the angle further positive, and with SPS12-R16100-05 to set to negative direction. From the negative angle set with the included washers, replace the washers with optional washers SPS12-R16100-05 to set the angle further negative, and with SPS12-R16100-25 to set to positive direction (both sold separately).
- Scion FR-S 2012–2016 (ZNA): Rear: interior needs to be cut or removed, to avoid interference. Camber adjustment washers with different offsets are available (sold separately). From the positive angle set with the included washers, replace the washers with optional washers SPS12-R16100-25 to set the angle further positive, and with SPS12-R16100-05 to set to negative direction. From the negative angle set with the included washers, replace the washers with optional washers SPS12-R16100-05 to set the angle further negative, and with SPS12-R16100-25 to set to positive direction (both sold separately).
